Find out 7 easy tips how to turn on electric water heater in house

Imagine you have installed an electric water heater for the first time, and you have no idea how to turn on electric water heater in house. If this happens in your house, then that is ok. But, if this happens somewhere else, that is an awful situation indeed. Though that seems very simple, you have to follow some steps to turn on the electric water heater. Otherwise, it won’t run and damage prematurely.
In this article, we will tell you how to turn on the electric water heater in the house step by step. You don’t need to have a lot of plumbing knowledge you alone can turn on the electric water heater. Let’s get started.

How does an electric water heater work?

Although electric heater varies model to model, their operating procedure is almost similar. An electric water heater heats water with two heating elements when it gets electric power. It has both a cold water inlet that fills the tank with cold water and a hot water outlet that discharges the water from the faucet when the water is warm enough.
There is a thermostat that is mounted to the side of the internal tank. When the thermostat detects that the internal water temperature is below the preset threshold, it triggers the switch that flows electricity to the heating element.
The incoming cold water pipe attaches to the dip tube into the water heater. The dip tube distributes the incoming water to the bottom of the tank to ensure all of the water is heated entirely. When the thermostat detects that the tank’s water reaches the preset temperature, it stops the power. Then, you will get the desired temperature of warm water from your hot water tap.

How to turn on electric water heater in house?

There are some steps that you might follow if your hot water tank is newly installed or need to clean. Don’t skip any of the steps while turning on the heater. Any negligence may occur in a significant accident or damage to the heater.

Credit: HouseImprovements

Step-1: Make sure there is no open valve, faucet

To turn on a water heater, at first, you have to make sure there are no open valves and the hot water tap that is connected with the heater. If you turn on the heater with an open valve or water faucet, this will create an airlock. So, check all the water faucets that are connected with the water heater, whether they are open or close.

Step -2:Fill up the tank with a cold water supply

Turn on the cold water valve of the tank to refill the tank with water. You can turn on the tank when it refills with cold water. At this point, you may have a question in your mind, “How do I know if my hot water tank is full of water?” There is a simple way that you can know when your tank is full. Open hot water faucet, if the water flow from the tap is normal, then your tank is full. If your water tap is not streaming enough flow of water, you should wait for some minutes until you see a usual stream of water.

Turn on the cold water valve

Step-3: Take out the safety tag

Your safety tag over your breaker may be placed. Usually, the safety tag of a water heart is placed to prevent anyone from turning on the switch or preventing electric shock. If the house is yours, then you have an idea about the safety tag. If the house is not yours, don’t forget to check whether the safety tag is placed or not. If a safety tag is placed, you must take it out to turn on the heater.

Step-4: Turn on the breaker

The final step to turn on an electric water heater is to turn on the breaker of the tank. When you turn on the breaker, there should a low sound that indicates the heater is running. Besides, you can check by opening a water faucet after some time to make sure the water is warming

Turn on the breaker

Step-5: Wait for several minutes

It takes several minutes to heat the water to the preset point. The preset point should at 120 degrees Fahrenheit (49 degrees Celsius.) Usually, it takes 30-40 minutes but, it may vary by the model.

Cautions about tuning on the heater

When turning on the HOT WATER HEATER which would be a little bit risky. If you are not careful when turning on a water heater, you may face serious accidents. To prevent any accident or to prevent premature damage to the water heater, some precautions should follow when turning on the heater. Here are some cautions that you must follow

  • Make sure your discharge pipes have no drips. Drips may increase the pressure too high. If you see any drips in your discharge pipe, turn the pressure down (the pressure should below 80 psi) before turning on the heater.
  • Make sure your water heater is safe for re-lighting and the pressure relief valves are working smoothly.
  • Check if there is any bare wire or clutter. If so, then do not re-light the heater before fixing the problem.
  • If your water heater is turning off automatically without heating the water, yes, your heater needs servicing. Sometimes, it may fix by replacing the fuse or resetting the breaker. If the problem is not solved with this process, then you should call a qualified plumber who can repair the electric water heater.
  • Most of the water heater comes with a guideline. If you are having any trouble, you can solve those with the water heater guideline.
  • Do not touch any part of the inside casing when the heater is running. It may cause a significant electric shock.

Frequently Asked Questions

Why is my electric water heater not making hot water?

An electric water heater cannot make hot water for some reasons. The most common problem is out of power supply, undersize water heater, tripped limit switch, or faulty heating element. At first, check the circuit breaker of the heater whether it is tripped off or not. If the problem is not there, it would be better to call a plumber to solve the problem

How do I know if my electric water heater is heating the cold water?

The most effective way of knowing if the water heater is heating up or not is to check the water in the tank. You can open a faucet that is connected with the water heater to know if your water heater is working. Please do not check immediately after turning on the heater. Wait for some minutes and check.

Do electric water heaters have a reset button?

Yes, almost all the electric water heater a reset button. But the position of the button varies from model to model. The button is usually red and usually located beside the thermostat. It may also behind a removable metal panel on the unit—and then behind some insulation. The best way is to find it in your manual of the heater.

Can water heaters be repaired?

If your water heater is less than ten years, it can be repaired if some problem occurs because a heater for more than ten years starts to damage day by day. But sometimes repairment needs equal cost of replacement. Then, we prefer to replace your water heater if the repairment cost is too high.

Can you change a water heater element without draining the tank?

Who wants to spend a lot of money on replacing the whole water heater when he/she can only replace a part of the tank? Of course, it is better to replace the heater element without draining the whole tank. Only if the problem of the heater is solved by replacing the heating element.

Finally
In the world of modern science and technology, we all have to keep us every step with time. Turning on an electric water heater is not a big issue. In this article, we have elucidated some easy steps about how to turn on the electric water heater in the house. If you read the article and follow the steps carefully, now, you don’t have to take stress about turning on a water heater.


Leave a Comment